Page Comparison

The flight controller implements a number of critical (FC) implements several low-level behaviors, e.g., stabilizing the drone Duckiedrone around roll, pitch, and yaw through three different PID controllers. Correctly configuring the FC is critical for flying safely.

Installing Cleanflight Configurator (CFC)

Cleanflight configurator is an app that allows the base station to connect directly to the FC and access its configuration interface.

Steps:

• Install Google Chrome

• Install the Cleanflight Configurator for Chrome

Updating the FC firmware

(Update to BTFL 3.3.3 - although successful flight tests have been conducted with 2.4.0 and 3.0.1)

• Start CFC on your base station. You should see the below interface.

...

Connecting to the Flight Controller (FC)

...

1. Unplug the battery from your drone

   1. Status
      colour Red title IMPORTANT

      double-check the battery is unplugged

2. Disconnect the Raspberry Pi from the FC

3. Connect the mini USB cable to from your FC and to your base station

4. Start CFC on your base station

...

1. In CFC (see last section), on the top right corner

   Image Added

   1. select the correct connection port

      • Status
        colour Yellow title Note

        Details might vary depending on available connections on your base station

...

1. 1. • . The correct port should start with: /dev/tty.usbserial*

...

1. 1. • /dev/cu.usbserial*

...

1. 1. • or /dev/ttyUSB*

   2. Leave the baud rate (number) at the

      Status
      colour Green title default

      value of 115200

...

1. Press

...

...

1. the “Connect” button and a “Setup” page should greet you with a rendering of your drone

...

This page can be used to do a quick test of the onboard IMU. You can move your drone around and verify that the rendering of the drone moves. Don’t expect it to be perfect, we still need to calibrate everything. We will come back to this page later while performing calibrations (https://ethidsc.atlassian.net/l/cp/WNont9ZB).

Configuration

Power and battery page

Image Removed

Failsafe page

...

PID tuning

...

Receiver

Image Removed

Modes

...

Adjustments

Image Removed

Servos

Image Removed

GPS (ignorOSD (ignore)

Race Transponder (ignore)

...

Sensors

...

Thethered Logging (ignore)

Blackbox (ignore)

...

1. (see figure below). Before configuring anything, please read the next section and flash the firmware.

...

Checking the existing firmware version

On the top left of the CFC interface, one could check for the Firmware version. For example, in the figure below, the firmware version of the FC is BTFL 3.3.3.

...

Prepare for flashing the FC firmware

• If the CFC is still connected to the FC, please press the “Disconnect” button on the top right.

...

• In the default Welcome page of CFC, in the left sidebar, please click on the Firmware Flasher tab

...

• Configure the options in the tab as below:

...

Updating the FC firmware (Flashing the FC)

FCs might have different versions of firmware (i.e., the software that runs on the FC’s micro-controller) out of the factory. Normally, this only needs to be done once initially. Follow this procedure to update your firmware.

• Status
  colour Red title IMPORTANT

  During flashing, do not press the “Connect” button in CFC.

• Status
  colour Blue title FACt

  Our current target firmware is: BTFL 3.3.3 (Download the .hex file below to your base station)

Different FC versions

Version	Picture and key features to notice for this section
ACRO	There is a micro USB port soldered on the board (In the figure blow, on the bottom right of the board ) There is a “BOOT” button. Image Added
OSD	There is no micro USB port As highlighted, the Boot pins are exposed near the “BO”marking. Image Added

Flashing the FC

The videos to flash respectively the ACRO version and the OSD version of FCs are below in this section. A summary is provided here. Most operations are the same with both versions, and any version-wise operations are highlighted with

1. Normally, when connected to the base station, the FC goes in Normal mode

   1. Status
      colour Green title check

      there is a red blinking LED

   2. unplug from base station

2. To flash the firmware, we would like the FC to be in Bootloader mode instead

   1. Status
      colour Purple title 1

      For the ACRO version, hold the “BOOT” button while connecting the FC to base station

      1. Status
         colour Purple title 1

         Once connected, one could release the boot button

      2. Status
         colour Purple title 1

         Status
         colour Green title check

         there is no red blinking LED. On the ACRO version, there is a solid blue LED

   2. Status
      colour Yellow title 2

      For the OSD version, use some conductive metal tool to short the “Boot pins” (as highlighted in the previous section)

      1. Status
         colour Yellow title 2

         Once connected, once could take the pin-shorting material/tool away

      2. Status
         colour Yellow title 2

         Status
         colour Green title check

         there is no red blinking LED. On the OSD version, there is no LED on now.

3. In the CFC Firmware Flasher tab, click the Load Firmware [Local] button (bottom right), and select the .hex file downloaded at the beginning of this section.

   1. Status
      colour Green title check

      The progress bar should look like “Loaded Local Firmware: (… bytes)”

4. Click the Flash Firmware button (bottom right) and check the progress bar.

   1. Status
      colour Green title check

      The progress bar shows: “Flashing…” => “Verifying…” => “Programming SUCCESSFUL”

   2. In case the progress bar turns red, see the Troubleshooting section below

5. If successful, without needing to reconnect the cable, the FC should go back to the Normal mode.

   1. Status
      colour Green title Check

      Verify the red blinking LED is back on

   2. Status
      colour Green title Check

      Click “Connect” and verify the firmware version is correct

...

Troubleshooting

...

You now have the updated flight controller firmware! Connect to it in Normal mode and we will configure it next.